How to setup Kitchen Display System RPE

 

How to setup Kitchen Display System RPE

Follow along as we set up a KDS (Kitchen Display System) also refered to as a Bumpbar system or Video Display System to display your pcAmerica restaurant pro food orders to a kitchen monitor instead of an impact printer.

We will be following the instructions from the pcAmerica FAQ site and installing the Bematech LS6000 with the Keypad Bumpbar KB1700G )

Bematech LS6000

Bematech LS6000

KB1700G

KB1700G

 

You will need to decide where you are putting the order screen. If you are placing the screen on a counter or shelf then it really doesn’t matter what type of monitor/TV you buy as long as it has a VGA port.

If you plan on mounting the monitor to a wall or ceiling bracket then look for a monitor that is VESA compliant. Which simply means it has screw holes for attaching to the brackets.

vesa compliant mounting

vesa compliant mounting

The instructions call for a special cable. Requires cable (P/N: KB17CABLE-RJRJ) to work with LS6000

The cable that came with the keypad does not have a part number on it.

 

When following the instructions (with a few changes) from the PCAmerica FAQ site I was able to get this up and running.

There are three documents on their site so please refer to them. I am only covering points that I feel need more elaboration.

The LS6000 has to be on the same subnet as your PC’s. So pull up the CMD (command prompt) and type in your “IPCONFIG”

On my Master computer you will see that my IP Address is 192.168.0.33 which is determined by my router.

 

CMD

Run the IPCONFIG in Command prompt

But since most PC’s are setup to be Dynamic IP addressing we have a couple choices. I am going to set my PC to a Static IP address.

If you find that your Bumpbar works but suddenly stops working after a reboot, it could be due to the Router assigning a different IP address to your Master computer. So for that reason I recommend setting it to Static.

Changing from Dynamic IP to Static IP address

#1  Next you will need to put in the IP Address and PORT number for the SERVER. If you don’t want to set your Master PC to Static IP address you can use the PC Name or “Localhost”. The instructions recommend using Port 42000. My LS6000 would only allow 4 characters. I was able to get it to work using multiple port numbers. I have it set to 500 for this example.

 

Input the IP Address, Computer Name or Localhost into this area. NOT the IP of the Bump Bar!

#2 Click on the “Edit Bump Bars” button

And input the IP Address of the LS6000 and use the Port number you set up in the Bematech LS6000 programming

In my case I’m using 192.168.0.55 and Port 500

This is where the IP Address of the Bumbar goes.

How to setup Kitchen Display System on Restaurant Pro 

The LS6000 output is a VGA port. My client said he wanted to use a 32″ inch TV he already had so I purchased this VGA2HDMI adapter. It does need power so make sure you have a USB port on your TV Monitor if you decide to go this route. Or purchase a power supply for it.

After setting this device up in my office on a test computer with much success, I decided to drive the nearly 300 miles to go install it in La Grande OR.

The first thing I did was to get on their backoffice computer and Ping for an open IP Address. I pulled up the CMD and ran the IPCONFIG first and it showed they were on 192.168.44.xxx

So I typed in PING 192.168.44.15 and it came back failed.  So that must mean that it was not being used. I decided to use that for the LS6000.

All is going well but after an hour of looking like an idiot and trying different port numbers because they had such a big network I figured some ports had to be blocked. Checked firewalls and still nothing!

Here I forgot the Start the SERVER and CLIENT as per the directions. UGH

I will be the first to admit I don’t work well in a store that is open and operating. People asking me questions, music too loud. Hustle and bustle. Give me nice and quiet remote support from my nice quiet office any day. =)

How to setup Kitchen Display System RPE

Leave a Reply

Your email address will not be published. Required fields are marked *

three × four =